Making bows of green wood Vol. 2- A very helpful jig

Another advantage of using green wood for to make selfbows is the possibility to shape it while drying. Vol. 1 was focused on working  a green bowstave a bit longer, wider and thicker than the final dimensions will be. So drying will help us again in making working easier.

But for to draw the drying wood into a shape a jig is needed, a kind of “shaper”. Don´t expect to much what is possible to get. I recommend slight deflex, reflex or recurve. For more curvature I reommend steam- bending( there will be an article about it soon). Anyway I´m not a friend of highly reflexed or recurved bows, maybe they are somehow looking wild or fast, but their performance is often quite disappointing compared with the challenge of making and shooting them.

The jig: as a mindful reader of the bowXplosion you still know it. It´s one of these multi- jigs I prefer so much, it could be used for heat- treating too. And its easy to do.

the jig- sideview, it´s 60" in length

It is made of a squared timber of douglas fir(2″ x 4″ in cross- section). Be generous and choose a real stable timber, maybe some found beech would be a better choice.  The curvature is suited for to get a slightly deflexed bow with long slightly reflexed tips. Usually bowyers have more jigs with different curves: more or no deflex, reflex all over the complete length, more reflex or even some more recurved tips. Anyway it is a good idea to have more than one of such jigs avaible, when a bow made of green wood is drying you can´t use the jig for heat- treating.

.......take care of the right angle.......

The most important thing is to get a right angle all over the length, otherwise you´ll end up with a twisted bow.

Draw parallel lines on the jig- at intervals of about 1/2"

The parallel lines are indicating a center- line for to fix the bow straight.

......the jig could also be used as a ruler for to check the straightness of a bow

Sorry this pic is not to good, but you see the string of this is running just at the edge of the handle:  the bow should be fixed at the jig  so, that the string is running a bit more towards the center of the handle. Heat- treating is so genius, it is possible to correct twists, to add deflex or reflex and at the same time drawweight is increasing!

Heat- treating or drying- jig without curves

Anyway it is possible to use a squared timber without sawing any curves, just straight and stable enough, the shaping could be done by using blocks of wood or cork  as displayed above.

Next volume is dealing with tillering the dried bow.



Advertisements

Making bows of Green wood Vol.1- Rowan flightbow

O.k., first article 2011. It´s a “to be continued” of “Bow- staves- Vol.2- making a bow from green wood”

The mentioned rowan- bow is ready, but to far away from 50lbs at 23″: 27lbs at 23″, what´s wrong about it? I did the bow to thin! That´s all, cause of my lack of experience in making bows of rowan- saplings. To fail is the teacher you´ll never forget.

Anyway I heat- treated much more reflex into the bow, I didn´t succeed in increasing the drawweight: if there is to less material, it is a no- go to enforce a selfbow. It´s quite better to cut away to less wood 20 times than to cut to much wood away one time! It´s not possible to add wood to a selfbow. Usually I keep such a failed bow, sooner or later a customer will ask for it.

The bow was tested, 27lbs at 23″, I did no chronos, it shoots a 350grs.- arrow at about 130yards.

th rowan bow is on the left
The rowan bow at 18"- checking the tiller

Beside the failed drawweight the bow is matching my expectations. I want the slightly reflexed limbs to become straight when drawn, most working is just beside the handle, so there is a quite well energy- storage.

This bow is a kind of study for to more get confident with the deflex/reflex- design I´m actually studying.

The second trial with a rowan- sapling:

The rowan stave

What looks straight is a bit snaky and twisty too, but with someheat-treating I could get by with it.

This stave is still green too

Cause the stave is green, it´s really easy to straighten it finally, but there´ll remain some tracks of its naturally growing- pattern. That´s what makes selfbows such distinctively genuine.

Checking the center- line of the stave

The handle is almost completely beside the center- line. Laying out the handle and the skinny tips. I wanted to make a longer handle as usual for to shorten the working area of the limbs. Combined with the skinny tips, this is a way for to mix the qualities of a longer bow with the capablities of a shorter bow: good leverage and a quick movement of the limbs.

Working the stave roughly with the ax

My Swedish ax is one of the best tools I´ve ever bought, this blacksmith is making single pieces, just tell him what you want. The most important thing is a premium blade, highly durable and not to heavy. If an ax is to heavy, it is not possible to make exactly cuts and your hands will be tired soon.

Using my shaving horse beside the warm wood-stove while winter has heavily begun

 

The design is cut
The skinny tips- finally the tips will be thicker than the bending/working parts of the limbs
The extra long handle
So far: the bow is ready for to clamped on the jig
So far: the bow is ready for to be clamped on the jig

Next volume will be focused on making a jig for drying a greenwood- bow, it could also be used for heat- treating.



A Great 2011 to all of my readers…………

The BowXplsion has become a very well visited blog, sometimes I´ve look at rankings:  alexa ranking for the BowXplosion is 56700, that´s so great, thanks to you!! I guess the BowXplosion is one of the top ten bowery sites worldwide, again thanks to you!! Keep on reading, I hope to be able to blog much more, I´ve so much bowery stories to tell.

I want you for more comments and questions, feel free to ask any bowery related question, I offer you my experience here, but I don´t know everything. Much more interaction is good for any blog………….

o.k., here is our magpie saluting the New Year, unbelievable………I don´t know where he learned this New Orleans- style melody!!!!!!! go for: elliott saluting 2011